Links
  • Compare ()
  • Sign In
  • Create an Account
Menu
Account
Toggle Nav
Cart 0 Shopping Cart

What are the general specifications for Full Access Cabinetry?

General Information
Cabinets are available in 0.1mm (.001") increments.
Choose either pre-finished maple UV interior, or unfinished (raw) interior (species available listed below).
All parts including Back panels are 3/4" PureBond® plywood.
Cabinet box plywood is light color domestic hardwood unless otherwise specified.
Back panel has a 10mm (.3937") scribe between the back and the wall (to accommodate Suspension System and allow scribing cabinet to fit wall irregularities).
Shelves are sized 3mm (1/8") less than the total inside width for easy adjustment.
Cabinets with Adjustable Shelves have the side panels bored for 5mm shelf pins on 32mm centers
(pins not included), these 5mm shelf holes are in pods of 5 holes.
Cabinet Components are available in the following wood species:

  • Alder
  • Cherry
  • Hard Maple
  • Hickory
  • Red Oak
  • Walnut
  • White Oak

Related Questions:

  1. Do you have written instructions on how to install Full Access Cabinetry?
  2. Why should I use the metric measuring system?
  3. What is the 32mm System?
  4. Why should I try to stay in system?
  5. Do you have Face Frame cabinets?
  6. Cabinotch Request a Quote - Material and Machining Options
  7. Cabinotch Request a Quote - Exterior Material
  8. Cabinotch Request a Quote - Interior Material
  9. Cabinotch Request a Quote - Drawer Box Material
  10. Cabinotch Request a Quote - Edgeband for Front Edge of Cabinets
  11. Cabinotch Request a Quote - Suspension System Machining
  12. Cabinotch Request a Quote - Leg Leveler Machining
  13. Cabinotch Request a Quote - Construction Method
  14. Cabinotch Request a Quote - Door Hinge Loc.
  15. Cabinotch Request a Quote - Edgeband for Adj Shelves
  16. Cabinotch Request a Quote - Edgeband Top and Btm of Upper Cabinet Sides
  17. Cabinotch Request a Quote - Validation Report - Full Access
  18. What are the advantages and disadvantages of Applied Ends versus Integral Finished Ends
  19. * What are KCD Quickstart Jobs?
  20. Why is the mid-rail below my top drawer offset (not centered)?
  21. Why can't I make Drawer Front height less than 148mm (5-13/16")?
  22. How do I make my top Drawer Front default to something other than 157mm (6-3/16")?
  23. Why are your Wall Cabinets 330mm (13") deep?
  24. Does your Base Sink Cabinet accommodate Tip-Out-Trays?
  25. * What is Frieze, and how does it work?
  26. * How does the Full Access Oven Cabinet work?
  27. * How does the Full Access Blind Corner Cabinet work?
  28. * How does the Full Access Angled Cabinet work?
  29. * How does the Full Access Clipped Cabinet work?
  30. Applied Panels, how do they work?
  31. Fillers vs. Applied Panels?
  32. What edges do you edgeband?
  33. What edgeband options do you offer?
  34. What edgeband color matches your white melamine?
  35. What edgebanding do you use on Raw Interior Cabinets? (KCD Only)
  36. How big is the pallet my parts will be shipped on?
  37. * What is the best way to check-in my Cabinotch Component parts?
  38. How does your standard base cabinet end panel layout?
  39. * Which Lamello P-14 Fastener goes where?
  40. Do I need to glue the joints when assembling these Full Access Cabinets?
  41. What screws should I use to assemble my cabinets?
  42. Are there any specialty tools I will need to assemble my Cabinotch Full Access Cabinetry?
  43. * What is the best assembly sequence for Cabinotch Full Access Cabinetry?
  44. Why are there 15mm holes in the bottom of my Base Diagonal and Piecut Corner Cabinets?
  45. How do I assemble my Base Piecut Corner Cabinets?
  46. Why is there a 10mm (approximately 3/8") space behind my Full Access cabinet backs?
  47. Why should I use Leg Levelers?
  48. Why should I use the Suspension System for my Upper Cabinets?
  49. Where do I locate the Suspension Rail on the wall for my Upper Cabinets?
  50. Why do I have to hinge my doors in KCD?
  51. Where do I bore my Hinge Holes in my Doors?
  52. What Reveals should I use on Corner/Diagonal Cabinets?
  53. Do I have to use any particular brand of Hinge?
  54. What Hinge and Hinge Plate should I use?
  55. How many Hinge Plates will you machine for?
  56. What are my Drawer Guide options?
  57. Where are the Drawer Guide holes located?
  58. Where do I position my Drawer Fronts on my Drawer Boxes?
  59. How deep (front to back) will my Drawer Boxes be?
  60. What height Drawer Box will my cabinets have if I purchase my drawer boxes from Cabinotch?
  61. KCD Release Notes - 2018-Current
FAQ Categories
  1. FAQ-Face Frame Cabinetry-KCD (30)
  2. FAQ-Face Frame Cabinetry-Webstore (41)
  3. FAQ-Full Access Cabinetry-KCD (62)
  4. FAQ-Full Access Cabinetry-Webstore (73)
  5. FAQ-WebStore (7)
  6. FAQ-Drawer Boxes (8)