Cabinotch Request a Quote - Construction Method

Related Questions:

1. What are the general specifications for Full Access Cabinetry?
2. Do you have written instructions on how to install Full Access Cabinetry?
3. Why should I use the metric measuring system?
4. What is the 32mm System?
5. Why should I try to stay in system?
6. Do you have Face Frame cabinets?
7. Cabinotch Request a Quote - Material and Machining Options
8. Cabinotch Request a Quote - Exterior Material
9. Cabinotch Request a Quote - Interior Material
10. Cabinotch Request a Quote - Drawer Box Material
11. Cabinotch Request a Quote - Edgeband for Front Edge of Cabinets
12. Cabinotch Request a Quote - Suspension System Machining
13. Cabinotch Request a Quote - Leg Leveler Machining
14. Cabinotch Request a Quote - Door Hinge Loc.
15. Cabinotch Request a Quote - Edgeband for Adj Shelves
16. Cabinotch Request a Quote - Edgeband Top and Btm of Upper Cabinet Sides
17. Cabinotch Request a Quote - Validation Report - Full Access
18. What are the advantages and disadvantages of Applied Ends versus Integral Finished Ends
19. * What are KCD Quickstart Jobs?
20. Why is the mid-rail below my top drawer offset (not centered)?
21. Why can't I make Drawer Front height less than 148mm (5-13/16")?
22. How do I make my top Drawer Front default to something other than 157mm (6-3/16")?
23. Why are your Wall Cabinets 330mm (13") deep?
24. Does your Base Sink Cabinet accommodate Tip-Out-Trays?
25. * What is Frieze, and how does it work?
26. * How does the Full Access Oven Cabinet work?
27. * How does the Full Access Blind Corner Cabinet work?
28. * How does the Full Access Angled Cabinet work?
29. * How does the Full Access Clipped Cabinet work?
30. Applied Panels, how do they work?
31. Fillers vs. Applied Panels?
32. What edges do you edgeband?
33. What edgeband options do you offer?
34. What edgeband color matches your white melamine?
35. What edgebanding do you use on Raw Interior Cabinets? (KCD Only)
36. How big is the pallet my parts will be shipped on?
37. * What is the best way to check-in my Cabinotch Component parts?
38. How does your standard base cabinet end panel layout?
39. * Which Lamello P-14 Fastener goes where?
40. Do I need to glue the joints when assembling these Full Access Cabinets?
41. What screws should I use to assemble my cabinets?
42. Are there any specialty tools I will need to assemble my Cabinotch Full Access Cabinetry?
43. * What is the best assembly sequence for Cabinotch Full Access Cabinetry?
44. Why are there 15mm holes in the bottom of my Base Diagonal and Piecut Corner Cabinets?
45. How do I assemble my Base Piecut Corner Cabinets?
46. Why is there a 10mm (approximately 3/8") space behind my Full Access cabinet backs?
47. Why should I use Leg Levelers?
48. Why should I use the Suspension System for my Upper Cabinets?
49. Where do I locate the Suspension Rail on the wall for my Upper Cabinets?
50. Why do I have to hinge my doors in KCD?
51. Where do I bore my Hinge Holes in my Doors?
52. What Reveals should I use on Corner/Diagonal Cabinets?
53. Do I have to use any particular brand of Hinge?
54. What Hinge and Hinge Plate should I use?
55. How many Hinge Plates will you machine for?
56. What are my Drawer Guide options?
57. Where are the Drawer Guide holes located?
58. Where do I position my Drawer Fronts on my Drawer Boxes?
59. How deep (front to back) will my Drawer Boxes be?
60. What height Drawer Box will my cabinets have if I purchase my drawer boxes from Cabinotch?
61. KCD Release Notes - 2018-Current